"He that respects himself is safe from others; he wears a coat of mail that none can pierce."
                -- Henry Wadsworth Longfellow

Author Topic: Rust, preventing and cleaning  (Read 109230 times)

Sir Edward

  • Forum Admin
  • Commander of the Order
  • Forum Veteran
  • *****
  • Posts: 9,340
  • Verum et Honorem.
    • ed.toton.org
Rust, preventing and cleaning
« on: 2012-08-19, 12:33:17 »

I admittedly only searched briefly before giving up, but I couldn't remember which threads we've talked about rust prevention and clean-up, and some of the problems some of us have been having lately, so I thought I'd start a new thread.

I never used to have much trouble with rust, or what little I did I was able to clean up with a little CLR. On items where I didn't mind messing up the finish (really cheap swords, the inside surfaces of armor), I've used wire-wheels on a drill, or small polishing wheels on the Dremel. It's quick and effective.

Mineral oil is what I've used for years to protect swords, and it must be working, since my Albion blades all look great (hilts are another story).

Recently I've been using CLR with steel wool, then quickly going over it with WD-40 to get the moisture out, then re-sealing with with either spray-on gun-oil, or Mineral Oil. This has failed miserably. As we discussed in another thread, both Sir James and I had problems with these items showing rust overnight, or over the first week. We've suspected both the gun oil, and the steel wool as being problematic here.

So I'm trying an experiment now.



I cleaned up my gauntlets, yet again (third time since this spring), and my brand-new helm, which I've never used, was still coated in whatever it shipped in, and yet still rusted a 6-inch long splotch on the back plus a few other splotches.

Right Gauntlet:  Turtle chrome polish,  WD-40, then Turtle wax.

Left Gauntlet: Metal-Glo, WD-40, then Ren-wax.

Helm:  Turtle chrome polish, WD-40, then Ren-wax.

I did all of these with scotchbrites and paper towels.

Immediately, the left gaunt doesn't look as good, since the metal-glo isn't a good rust remover. And while CLR with steel wool eats up the rust more quickly than the above options, it has problems, in that it's very watery and runs everywhere, whereas the others above are more thick. And I need to avoid the steel wool.

I also did a really quick pass over the fingers on the gaunts, so they don't look that great right now.

Another thing I'm tempted to do, is a CLR clean-up, and go over it with windex and let it dry. Then WD-40, and on to a sealant. I've used Windex on the swords before, and it's a nice soft soap to get oily crap off. But anything that's water based needs to use WD-40 and/or dry off.

Let's keep a good discussion going. Clearly we'll all have varying experiences, but hopefully we can come up with some really good methods.


Sir Ed T. Toton III
Knight Commander, Order of the Marshal

( Personal Site | My Facebook )

Sir Edward

  • Forum Admin
  • Commander of the Order
  • Forum Veteran
  • *****
  • Posts: 9,340
  • Verum et Honorem.
    • ed.toton.org
Re: Rust, preventing and cleaning
« Reply #1 on: 2012-08-19, 15:01:56 »

BTW, thread is sticky so we can always find this.
Sir Ed T. Toton III
Knight Commander, Order of the Marshal

( Personal Site | My Facebook )

Ian

  • Knight of the Order
  • Forum Veteran
  • ****
  • Posts: 2,994
Re: Rust, preventing and cleaning
« Reply #2 on: 2012-08-19, 15:21:28 »
I've posted this before, but will repost for the sticky:

My most successful rust prevention / cleaning method has been the use of BreakFree CLP (Cleaner / Lubricant / Preservative).  After wearing my armor, I will remove any dirt/dust with an old t-shirt or sock.  Then if there is any surface rust present, I will work it off using a green scrubby or appropriate grit scotch-brite pad (depending on level of polish), with a dab of CLP.  For more stubborn rust, let the CLP sit on the surface a bit before scrubbing like you would a fouled firearm barrel.

After the surface rust is removed, I will then apply a light coating of CLP to the entire surface of the metal.  Over time CLP thickens up a little bit and acts as a barrier to moisture and prevents rust rather effectively.  I have 2 helmets and a pair of hourglass gauntlets on display in my home that have not been treated in several months.  They sit in free air 24/7, and are occasionally exposed to humidity.  There are no signs of any surface rust on their surfaces.  I use this stuff on both armor and swords with excellent results.

Don't take my word for it, take Albion Swords' word for it:
From Albion's Sword Care Page
Quote
Regular Maintenance
After handling, cutting, or after six months of storage or display, the metal components should be wiped clean with a soft cloth, and lightly oiled with a quality machine or gun oil. We strongly recommend Break-Free CLP as the premium oil for this use - it is the same oil that we use prior to shipping the finished pieces from our shop. A more traditional approach would be to use a quality mineral oil, although it would require more frequent application.

« Last Edit: 2012-08-19, 15:25:29 by Ian »
My YouTube Channel - Knyght Errant
My Pinterest

Qui desiderat pacem, praeparet bellum

Sir James A

  • Weapons & Armor addict
  • Knight of the Order
  • Forum Veteran
  • ****
  • Posts: 6,043
Re: Rust, preventing and cleaning
« Reply #3 on: 2012-08-19, 22:58:33 »
I narrowed my rapid-rust assault issues down to being the "blue CLR" by Zep. The grey CLR, the regular "Calcium Lime Rust", worked well. Ironically, both of them are sold at Home Depot. I haven't found any reason for the difference between the two (chemically), but it's night and day. I've got pieces I've cleaned with grey CLR and used the gun oil on from weeks ago that haven't showed a bit of rust yet.

My thought is that the rusting GDFB sabatons was a fluke, and the spray-on gun oil oversprayed when I was cleaning the cuisses in front of them, and that the overspray was probably "bounce off spray" that was contaminated with "blue CLR" from the cuisses. To confirm, I sprayed a few junk pieces with the RemOil gun oil, and had no rusting problems when the "blue CLR" wasn't used. When I sold my SCA gear last month or so, I started to clean it up with blue CLR, and it had turned green (starting to oxidize) within hours - I caught it before it went to epic rust level, which is when I knew it was the CLR, as I had done nothing but clean it and let it air dry - no WD40, no gun oil, no wax, nothing but the blue CLR.

I've got a "mix and match" of WD-40, "Grey CLR", RemOil spray gun oil, Eezox spray gun oil, and BreakFree CLP spray oil. I've also got some SC Johnson Floor Wax (low/no acid) that I picked up from Home Depot; one of the harnesses I bought had this on it already - the entire upper of the one I wore at VARF - and none of it rusted, except a few spots on the breastplate (from excessive sweat). The previous owner of the harness said it was recommended to him by someone who worked in the medieval armor section of the Met in NY (where the seller was from).

I've been doing rust removal with ScotchBrite grey ultra-fine pads and the grey CLR. For some of the stubborn spots, I've used the tiny wire wheels or wire cups on the dremel; it leaves black marks, but the scotchbrite and CLR takes care of those.

The most important thing is to get it before it starts pitting; after that, the metal is damaged and not reasonably repairable. As long as the maintenance is kept up with, almost any of the protectants will work fine; some better than others, of course, but as long as you put *something* on to protect it, and keep an eye on it, it'll serve you well.
Knight, Order of the Marshal
Sable, a chevron between three lions statant Argent

Sir Edward

  • Forum Admin
  • Commander of the Order
  • Forum Veteran
  • *****
  • Posts: 9,340
  • Verum et Honorem.
    • ed.toton.org
Re: Rust, preventing and cleaning
« Reply #4 on: 2012-08-20, 01:32:52 »

Those grey scotchbrites are fantastic. They're the ones Albion recommends, and uses for their finishing. You can wipe down Albions with them and not alter the finish, as a result.
Sir Ed T. Toton III
Knight Commander, Order of the Marshal

( Personal Site | My Facebook )

Lord Dane

  • The Hound, Hunter, and Hammer of Justice
  • Knight of the Order
  • Forum Acolyte
  • ****
  • Posts: 1,900
  • Selflessness, Service, Justice.
Re: Rust, preventing and cleaning
« Reply #5 on: 2012-08-20, 01:36:59 »

Those grey scotchbrites are fantastic. They're the ones Albion recommends, and uses for their finishing. You can wipe down Albions with them and not alter the finish, as a result.

What's recommended for the finish on polished stainless steel to regain its luster after stripping off the rust, particularly my Windlass arming sword??
"Fides, Honos, Prudentia, Sapiencia" (Faith, Honor, Prudence, Wisdom)
"Fiat justitia ruat caelum" (Let justice be done)

Sir Brian

  • Knight of the Order
  • Forum Veteran
  • ****
  • Posts: 4,735
  • Felix uxor beatam vitam - Happy Wife Happy Life
    • Order of the Marshal
Re: Rust, preventing and cleaning
« Reply #6 on: 2012-08-20, 15:46:56 »
My armor cleaning has always consisted of Turtle Chrome Polish/Rust Remover with a green scrub pad, wipe off with a rag then a good wipe down with Remmington gun oil. Really tough rust gets a steel wool scrub and the serious rust goes under a wire wheel.
"Chivalry our Strength, Brotherhood our sword"
Vert, on a Chief wavy Argent a Rose Sable,
a Gryphon Segreant Or

[img width=100 height=100]
<a href="http://s221.photobucket.com/user/Tah908/media/LP_Medals_zpsq7zzdvve.jpg.html" target="_blank"><img src="http://i221.photobucket.

merc3065

  • Forum Member
  • **
  • Posts: 56
  • New Member
Re: Rust, preventing and cleaning
« Reply #7 on: 2012-08-20, 17:52:18 »
I've been using a scotch brite pad with Tom's Secret Formula B404.  It's a natural corn oil that is non toxic.  I've not had any major rust issues until recently with leather soaking up tons of sweat moisture and causing some epic levels of rust underneath the leather strips on the back of the armour.

So I've had to work oil into those areas that are inaccessible just to slow the rust down.

I've had very good luck with the B404 and have been using it for almost a year now.  Biggest thing is to let the armour and leather dry after you've sweat in the stuff, then condition the leather and the metal after it's dried.  If there's enough residual oil or wax on it you generally won't get too much in the way of flash rusting as the moisture can't penetrate and affect the metal's surface.

Sir William

  • Cogito ergo sum
  • Knight of the Order
  • Forum Veteran
  • ****
  • Posts: 7,154
Re: Rust, preventing and cleaning
« Reply #8 on: 2012-08-21, 15:42:35 »
I use Flitz, and a microfiber or terry cloth to rub in and wipe down- it seems to work well on both armor and swords- altho in my case they're all carbon steel, non-stainless so there's that to consider.  I don't leave any of the items in any sort of protective enclosure- I've had some rust issues, usually after a hard day but beyond that, nothing that can't be cleaned up with a few sprays of Flitz and some elbow grease.
The Black Knight, Order of the Marshal
'Per Pale Azure and Sable, a Chevron counterchanged fimbriated argent.' 
“Pride makes a man, it drives him, it is the shield wall around his reputation.  Men die, but reputation does not.â€

Leganoth

  • Forum Follower
  • ***
  • Posts: 343
Re: Rust, preventing and cleaning
« Reply #9 on: 2012-08-22, 23:11:06 »
My main problem is finger stains/dirt from finger prints, thats what really bothers me, could never find a way to remove them and avoid it

Sir Edward

  • Forum Admin
  • Commander of the Order
  • Forum Veteran
  • *****
  • Posts: 9,340
  • Verum et Honorem.
    • ed.toton.org
Re: Rust, preventing and cleaning
« Reply #10 on: 2012-08-23, 00:19:59 »

Skin oils are corrosive to the steel, so the way to avoid it is to either not touch it (in the case of sword blades, touching the steel is easily avoidable and is a best practice anyway), or always wipe it down after handling it with fresh oil.
Sir Ed T. Toton III
Knight Commander, Order of the Marshal

( Personal Site | My Facebook )

Lord Dane

  • The Hound, Hunter, and Hammer of Justice
  • Knight of the Order
  • Forum Acolyte
  • ****
  • Posts: 1,900
  • Selflessness, Service, Justice.
Re: Rust, preventing and cleaning
« Reply #11 on: 2012-08-23, 07:37:29 »

Skin oils are corrosive to the steel, so the way to avoid it is to either not touch it (in the case of sword blades, touching the steel is easily avoidable and is a best practice anyway), or always wipe it down after handling it with fresh oil.

And wearing disposable powder-free, non-allergenic, medical gloves when handling or cleaning does not hurt either. Keep the sweat caused by humidity from your steel when cleaning if your outside. Best done in cool environment anyways (like indoors).
"Fides, Honos, Prudentia, Sapiencia" (Faith, Honor, Prudence, Wisdom)
"Fiat justitia ruat caelum" (Let justice be done)

Sir James A

  • Weapons & Armor addict
  • Knight of the Order
  • Forum Veteran
  • ****
  • Posts: 6,043
Re: Rust, preventing and cleaning
« Reply #12 on: 2012-08-23, 14:32:48 »
My main problem is finger stains/dirt from finger prints, thats what really bothers me, could never find a way to remove them and avoid it

As Sir Edward and Lord Dane said.

I'm becoming partial to the waxing, since the wax doesn't displace as easily as the oils, and seems to take handling better. My armor was handled to get it on at VARF, and other than the breastplate I was constantly sweating on, the pauldrons, arms, etc, didn't rust at all - and the only "cleaning" they got was a wipe with a towel - no extra wax or oil at all.

The other side is that it's more involved to remove and reseal the wax, or for cleaning.
Knight, Order of the Marshal
Sable, a chevron between three lions statant Argent

Sir Ulrich

  • Squire of the Order
  • Forum Acolyte
  • ***
  • Posts: 1,177
Re: Rust, preventing and cleaning
« Reply #13 on: 2012-09-19, 00:31:31 »
My new topfhelm is already rusting, gotta clean that off. Yet my kettle helm has been in RAIN STORMS and has never rusted. Maybe it's cause my kettle has a mirror finish while my Topfhelm is satan finished? Not sure.

Jessica Finley

  • New Forum Member
  • *
  • Posts: 43
  • New Member
Re: Rust, preventing and cleaning
« Reply #14 on: 2012-09-19, 02:11:03 »
Yup - the satin finish is (basically) tons of tiny grooves.  those grooves "catch" water, and encourage rust.  The smoother and shinier the polish, the less grooves, hence less rust.