"I fear not the man who has practiced ten thousand kicks once. But I fear the man who has practiced one kick ten thousand times."
                -- Bruce Lee

Author Topic: Wire wrapped handle  (Read 29139 times)

Sir James A

  • Weapons & Armor addict
  • Knight of the Order
  • Forum Veteran
  • ****
  • Posts: 6,043
Wire wrapped handle
« on: 2012-06-03, 01:50:42 »
A quick tutorial on wire wrapping a handle - usually would be a sword handle, but this applies to maces, war hammers, etc.

Start by disassembling the sword, if possible:


* A threaded allan key pommel isn't as historical as a peened pommel, but it makes this part easy and is more maintenance-friendly

On my sword, I removed the leather grip, and wire wrapped over the wood core. I painted it black so small spots I screw up won't be as obvious:



I placed a few inches of the wire inside the hollow part of the handle, and pushed it back onto the tang:



Wrap it around over and over. I've found the easiest way for me to do this is to rotate the sword itself, and to apply constant downward pressure facing away from my body. I can watch the sword to try to keep the wrapping tight, but it's a bit of a strain on my hands. Some wrapping done:



And finally, the finished handle:



This is, and I kid you not, a *very* slow process. This handle, a CAS/Hanwei Longsword, took me a solid 3 hours to do. And I made quite a few mistakes. The wire is *very* picky about being perfectly straight. Looking back at it, I should have used some pliers to straighten out the tiny little "kinks" in the wire; it would bend slight at spots when coming off the spool, and it affects the final appearance.

On the bright side, it's both cheap and easy to do. Total cost was $5 + tax, with some wire left over. I used simple black-coated brass wire from JoAnn Fabrics (or any other girly-stuff store). It was a 30 yard roll, and a bit of another. I used 26 gauge, and I didn't do the "twisted wire" style, just a straight wire wrap. And no more torn leather! Let's see how this holds up to gauntlets....
Knight, Order of the Marshal
Sable, a chevron between three lions statant Argent

Sir Rodney

  • Knight of the Order
  • Forum Acolyte
  • ****
  • Posts: 1,118
  • Inquit Corvus
    • The Mercenary Company Nevermore
Re: Wire wrapped handle
« Reply #1 on: 2012-06-04, 13:05:03 »
Nicely done!  I’m going to guess that you’ll eventually see a very attractive, almost antique-like, wear pattern as the black coating wears off the brass wire at the contact points with your gloves.  8)

Quote from: James Anderson III
This is, and I kid you not, a *very* slow process. This handle, a CAS/Hanwei Longsword, took me a solid 3 hours to do. And I made quite a few mistakes. The wire is *very* picky about being perfectly straight.

I helped a buddy do this once.  You’re not kidding.  Even with two people, one slowly turning the sword and one keeping tension / guiding the wire, this process takes a long time. The results are worth it though; my buddy’s hilt still looks great after 10 years!
"Oh, what sad times are these when passing ruffians can say Ni at will to old ladies. There is a pestilence upon this land, nothing is sacred. Even those who arrange and design shrubberies are under considerable economic stress in this period in history." - Roger the Shrubber

Sir Brian

  • Knight of the Order
  • Forum Veteran
  • ****
  • Posts: 4,735
  • Felix uxor beatam vitam - Happy Wife Happy Life
    • Order of the Marshal
Re: Wire wrapped handle
« Reply #2 on: 2012-06-04, 13:25:28 »
Well done Sir James! Another method for securing the beginning of the wire wrap on swords with peened pommels is drilling a small hole into the wood core approximately ¼” below the winding starting point and secure the wire with a dab of glue.  ;)
"Chivalry our Strength, Brotherhood our sword"
Vert, on a Chief wavy Argent a Rose Sable,
a Gryphon Segreant Or

[img width=100 height=100]
<a href="http://s221.photobucket.com/user/Tah908/media/LP_Medals_zpsq7zzdvve.jpg.html" target="_blank"><img src="http://i221.photobucket.

Sir Edward

  • Forum Admin
  • Commander of the Order
  • Forum Veteran
  • *****
  • Posts: 9,340
  • Verum et Honorem.
    • ed.toton.org
Re: Wire wrapped handle
« Reply #3 on: 2012-06-04, 15:02:32 »

Another way to pin the end of the wire is with an actual pin:


(clicky)
Sir Ed T. Toton III
Knight Commander, Order of the Marshal

( Personal Site | My Facebook )

Sir Patrick

  • Knight of the Order
  • Forum Acolyte
  • ****
  • Posts: 1,647
  • Nex pro inhonesto, Deus pro totus.
    • The Order of the Marshal
Re: Wire wrapped handle
« Reply #4 on: 2012-06-04, 17:21:51 »
Well done!  Should be worth all the effort in the long run.
Gules, a chevron argent between three cinquefoils ermine.
"Better to live one day as a lion, than a thousand as a lamb."
Knight, Order of the Marshal

Sir James A

  • Weapons & Armor addict
  • Knight of the Order
  • Forum Veteran
  • ****
  • Posts: 6,043
Re: Wire wrapped handle
« Reply #5 on: 2012-06-04, 18:45:18 »
The results are worth it though; my buddy’s hilt still looks great after 10 years!

Excellent, exactly what I hoped to hear.

Well done Sir James! Another method for securing the beginning of the wire wrap on swords with peened pommels is drilling a small hole into the wood core approximately ¼” below the winding starting point and secure the wire with a dab of glue.  ;)

I'll keep that in mind, I'll be trying this on a modified Kingdom of Heaven sword in the near future too. :)


Another way to pin the end of the wire is with an actual pin:


(clicky)

The wire wrap on your scabbard is one of the things that sold me on giving it a try. Somehow I blanked out the pins in memory. It just looks so awesome.
Knight, Order of the Marshal
Sable, a chevron between three lions statant Argent

Sir William

  • Cogito ergo sum
  • Knight of the Order
  • Forum Veteran
  • ****
  • Posts: 7,154
Re: Wire wrapped handle
« Reply #6 on: 2012-06-04, 21:10:39 »
Looks fantastic, Sir!  I was looking at acquiring some fine silver wire but missed the last day of the auction...relatively cheap too.  Nice look, there.
The Black Knight, Order of the Marshal
'Per Pale Azure and Sable, a Chevron counterchanged fimbriated argent.' 
“Pride makes a man, it drives him, it is the shield wall around his reputation.  Men die, but reputation does not.”

J.G.Elmslie

  • Newbie
  • Posts: 4
  • New Member
    • J.G.Elmslie, Cutler.
Re: Wire wrapped handle
« Reply #7 on: 2012-06-22, 00:13:13 »
Spotted this, and well, felt it might be of interest to people for me to contribute.
So, just registered, and here goes.

The plain straight wire method depicted in this is a fairly simple technique, and in silver, particularly suited to viking era hilts,  but as James Anderson's mentioned, its picky about straightness, and fiddly to get right.  For later medieval, however, an alternative is counter-spiralling wire, as used by Albion and the likes on their high-end hilts.
Quite a lot of people try it, not many get it right. so I thought I'd show people how:

(Since I dont have any swordhilts that need it done to them to hand right now, I'm afraid its that good old substitute, a hammer handle.)

So, what you need, tools-wise, is:
1 pair of wire cutters, 1 Hammer, 1 Drill hand drill, or one with a reverse. 1mm drill bit. Vise, or similar clamp for holding wire. Ball of string.
And a long corridor, hallway, back garden, or similar location you can stretch the wire out for several metres. 

Eye protection. bits of wire will whip around; trust me on this. Oh yes. Or "Arr, aye", as I say nowadays. 

Materials-wise: Wire. your choice.   
Pins: broad-headed, to pin down the wire. very small clout nails work, upholstery pins work very well. Or you can make non-ferrous broad-headed pins from bronze/brass stock soldered on to panel pin nails, without drawing the steel's temper if you're careful and stark raving mad.

Generally, I'd reccommend that you wrap the hilt in leather first, in the usual wet-forming technique with risers which I expect most people will know well enough. it gives a little bit of "give" which the wire can bite into .   


So, you've got your materials: handle/hilt, pins, and wire. I'll personally reccommend "the scientific wire company" as they do reels of iron, bronze, silver, or if you're  a sick deviated prevert, anodised aluminium. a 50gramme reel is easily enough for one hilt unless its a two-handed monster, I should add.

Stick 'em all together, you get something like this:



your first step is to use the ball of string. stick it onto your hilt where you want the wire wrap to start, and wrap it around, all the way to where you want to end. mark it, and unwrap from the hilt. That'll give you a good estimate of the length of wire you're going to need to do your wrap. Saves you screaming when you realise you're 6 inches short...

So. what you want to do for spiralling wire is take that measurement on the string, and half it, and add about two metres extra, so you've got a bit of extra. Now, what you want is to cut a wire that lenght, and loop it in half, and clamp it into the vise, and feed it out down the hallway or whatever nice open space you've got to hand.
 
sort of like this:



now, you want to stick the other end of the wire into the drill. A nice little effort-saving tip here: clamp the ends in the vise, and have a continuous loop of wire. instead of trying to attach the wire into the drill chuck, get a ? shaped hook, and clamp that in the chuck, and hook the wire over it. far, far easier to keep the wire in place and under a little tension.

with it all hooked up, start to turn the drill slowly, and the wire will start to spiral:



keep on going till you have a nice, tight spiral.

now, repeat the process all over, with a second length of wire. Only this time, reverse the drill, so the spiral is turning the other way.

when you've done that, you should have two lovely, straight spiralling wires, like this:




Now, you've got your hilt, and you've got your wires. 
Use the 1mm drill bit to drill pilot holes around the point where you want the wire to start. main reason for this is that its very easy to split the wood close to the edge with a nail, and this minimises it, and also guides the pin down straight.  I'd normally do 8 nails around the entire hilt, but for this, I'm being lazy and just one.
slip the wires underneath the pin when its just above the surface, then give it a good tap to bite the wires into the surface, and pin them in place.



Repeat all the way around the hilt, with at least half a dozen pins. so the wire is securely fixed in place.

Then feed the two spirals of wire around the hilt, and wrap it all the way up as far as you want it to be done. I'd reccommend wearing gloves, and feeding the wire over your thumb... the gloves will mean you dont saw a hole through your thumb after 2 inches of hilt.

when you reach the end of your hilt, I'd reccommend developing mutant powers, and with your second pair of hands, drill a second set of pilot holes for pins.  If you have more brain cells than I do, you might even figure out where you want your wrap to go to, before you start with the wire. it would be the sensible course of action, certainly.

Then, use a second set of pins, to hold the wire wrap end down. if you've got it right, it'll be nice and secure. if you got it wrong, expect wire to sproing out from under your pins, and unwrap into something like a bomb in a spring factory.

But if it works, you end up with something like this:




and if that's done on a proper hilt, that should end up looking something like these two:





Erm. Yep. something like that.

Hope its of interest to people.
And, since this is a first post, er... Hello.




Sir Brian

  • Knight of the Order
  • Forum Veteran
  • ****
  • Posts: 4,735
  • Felix uxor beatam vitam - Happy Wife Happy Life
    • Order of the Marshal
Re: Wire wrapped handle
« Reply #8 on: 2012-06-22, 01:22:19 »
Wow! Excellent first post! Oh and welcome to the forum! :)
"Chivalry our Strength, Brotherhood our sword"
Vert, on a Chief wavy Argent a Rose Sable,
a Gryphon Segreant Or

[img width=100 height=100]
<a href="http://s221.photobucket.com/user/Tah908/media/LP_Medals_zpsq7zzdvve.jpg.html" target="_blank"><img src="http://i221.photobucket.

Ian

  • Knight of the Order
  • Forum Veteran
  • ****
  • Posts: 2,994
Re: Wire wrapped handle
« Reply #9 on: 2012-06-22, 01:43:28 »
Excellent tutorial!  Very easy to follow, and very well done.  Thank you for that!
My YouTube Channel - Knyght Errant
My Pinterest

Qui desiderat pacem, praeparet bellum

Sir Wolf

  • He Who is Not to be Named
  • Knight of the Order
  • Forum Veteran
  • ****
  • Posts: 5,389
  • i have too many hats
    • man e faces
Re: Wire wrapped handle
« Reply #10 on: 2012-06-22, 02:04:59 »
Wow that was great. Thank you for sharing that

Sir James A

  • Weapons & Armor addict
  • Knight of the Order
  • Forum Veteran
  • ****
  • Posts: 6,043
Re: Wire wrapped handle
« Reply #11 on: 2012-06-22, 04:15:23 »
Great write up, thank you! Welcome to the forums!
Knight, Order of the Marshal
Sable, a chevron between three lions statant Argent

Lord Dane

  • The Hound, Hunter, and Hammer of Justice
  • Knight of the Order
  • Forum Acolyte
  • ****
  • Posts: 1,900
  • Selflessness, Service, Justice.
Re: Wire wrapped handle
« Reply #12 on: 2012-06-22, 13:03:01 »
Very pretty. Not exactly...stitch one, pearl two huh??  Wire-wrapping your sword grips is definitely time-foresaking but if done properly, the end result speaks for itself.  Looks great!!  I'll stick with the very fine wire that I'm used to working with.  Just did the grips on two wooden wasters of mine.  Not ready to armor my custom-swords yet.  Like them with the leather-cross bindings.  I'll put up some pics of my armory up for commentaries.
"Fides, Honos, Prudentia, Sapiencia" (Faith, Honor, Prudence, Wisdom)
"Fiat justitia ruat caelum" (Let justice be done)

Sir Edward

  • Forum Admin
  • Commander of the Order
  • Forum Veteran
  • *****
  • Posts: 9,340
  • Verum et Honorem.
    • ed.toton.org
Re: Wire wrapped handle
« Reply #13 on: 2012-06-22, 14:25:02 »

Great tutorial! Thank you very much for that.
Sir Ed T. Toton III
Knight Commander, Order of the Marshal

( Personal Site | My Facebook )

Sir William

  • Cogito ergo sum
  • Knight of the Order
  • Forum Veteran
  • ****
  • Posts: 7,154
Re: Wire wrapped handle
« Reply #14 on: 2012-06-22, 14:37:13 »
A fine first post, JG...welcome to the forums!
The Black Knight, Order of the Marshal
'Per Pale Azure and Sable, a Chevron counterchanged fimbriated argent.' 
“Pride makes a man, it drives him, it is the shield wall around his reputation.  Men die, but reputation does not.”